VITAMER
USER GUIDE

In order of 300ml / 350ml / 380ml / 400ml / 500ml / 500ml Pro

Welcome to #thevitamerlife! 

Scroll down to find your guide to everything that you need to know about using your Vitamer portable blender.

Thank you for choosing the Vitamer life.

Notice & Caution

Relevant for 350ml, 380ml, 400ml and 500ml portable blenders

Don't seperate the bottle and motor or open the bottle while the Vitamer is blending.

Easy Assemble

Use with caution to avoid physical injury.

Easy Wash

Don't start your Vitamer if the bottle is empty. This may cause the motor to overheat.

Easy Wash

Keep your Vitamer away from minors.

Easy Wash

Don't put your Vitamer into water hotter than 70° to avoid temperature distortion.

Easy Wash

Don't disassemble, reform or refit your Vitamer. This may cause it to malfunction, which can be dangerous.

Easy Wash

Don't wash your Vitamer with banana oil, gasoline, scouring powder or other corrosive liquid. This may damage the surface of your Vitamer.

Easy Wash

Keep your Vitamer away from a microwave oven, electric heater and other heating devices  to avoid discolouration or distortion.

Easy Wash

Although every Vitamer features "Safety Mode", we don't recommend pressing the 'on/off' button when the bottle and motor are detached.

VITAMER

300ml

How To Use

Step one
Fully charge your Vitamer

Fully charge until red light changes to white. Please only use your Vitamer charger.

Step two
Add your ingredients

Slice your fruits into small pieces. Add a small amount of liquid. The max amount of liquid that you can add at once should level with the bottom of the white rubber sleeve.

Step three
Connect

Tighten the bottle onto motor until the white light flashes. 

Step four
Juice

Double-click the orange power button. 
Tip: if the motor doesn’t switch on, the blades are blocked.

Step five
Auto-clean

Immediately after use, fill the bottle half-full with water, add a drop of soap, blend for 10 seconds, and then rinse the bottle and blades. Do not submerge the motor in water. Do not run water over the power button.

How to use your Vitamer 300ml

Here is a short video on how to use your Vitamer 300ml Portable Juicer.

VITAMER

350ml

How To Use

Step one
Fully charge your Vitamer

Fully charge until red light changes to white. Please only use your Vitamer charger.

Step two
Connect

Tighten bottle onto motor until white light flashes.

Step three
Add your ingredients

Put your liquid in first, followed by your fruit, ice or other ingredients.

Step four
Blend

Flip your Vitamer upside down, press and hold in the power button to start and then flip right way up. Tip: if the motor doesn’t switch on, the blades are blocked

Step five
Auto-clean

Immediately after use, fill the bottle half-full with water, add a drop of soap, blend for 10 seconds, and then rinse the bottle and blades. Do not submerge the motor in water. Washing note: when rinsing the blades, please be aware that the motor is water resistant and not fully water proof. Please don't submerge the base/motor part in water or pour water over the power button and charging port - rinse the blades and dry base/motor part.

How to use your Vitamer 350ml

Here is a short video on how to use your Vitamer 350ml Portable Blender.

Fault & Diagnosis

  1. Vitamer won't start
    Check:
    • If used continuously for a long time?
    • If the blade is stuck by ingredients?
    • If the bottle is connected to the motor correctly?
    • If the battery is flat?

    Solution:
    • Wait for the motor to cool down.
    • Remove the ingredients that's stuck - ensure that blades are clear.
    • Make sure that the bottle is properly tightened onto the motor/base.
    • Use after fully charged.
  2. Ingredients can't be blended
    Check:
    • Check if your ingredients are too much or too little?
    • If your cut cubes of ingredients are too big?
    • If you've got too little water/milk added?

    Solution:
    • Add enough ingredients.
    • Cut your cubes into smaller cubes.
    • Add water or milk.
  3. Red & white light flickers alternatively, and motor won't start
    Check:
    • If safety mode is activated?
    • If the battery is flat?

    Solution:
    • Retighten the bottle to the motor.
    • Charge the device.
  4. Red light flickers and motor won't start
    Check:
    • If the device is overloaded / blades are blocked?

    Solution:
    • Adjust your ingredients inside your Vitamer.
    • Ensure the blades are free to start spinning.

Charging

For first time use, please fully charge your 350ml Vitamer

LED light is red when charging. LED light is white when it is finished charging.

Easy Assemble

Press the 'on/off' button when the battery is fully charged, the white light will indicate that it is ready to blend.

Easy Wash

When the battery is low, the red and white light will flicker alternately.

VITAMER

380ml

How To Use

Step one
Fully charge your Vitamer

Fully charge until red light changes to green. Please only use your Vitamer charger.

Step two
Connect

Tighten bottle onto motor until green light flashes.

Step three
Add your ingredients

Put your liquid in first, followed by your fruit, ice and other ingredients.

Step four
Blend

Flip your Vitamer upside down, double-click the power button to start and then flip right way up. Tip: if the motor doesn’t switch on, the blades are blocked.

Step five
Auto-clean

Immediately after use, fill the bottle half-full with water, add a drop of soap, blend for 10 seconds, and then rinse the bottle and blades. Do not submerge the motor in water. Ensure your charging port flap is closed.

How to use your Vitamer 380ml

Here is a short video on how to use your Vitamer 380ml Portable Blender.

Fault & Diagnosis

  1. Vitamer won't start
    Check:
    • If used continuously for a long time?
    • If the blade is stuck by ingredients?
    • If the bottle is connected to the motor correctly?
    • If the battery is flat?

    Solution:
    • Wait for the motor to cool down.
    • Remove the ingredients that's stuck - ensure that blades are clear.
    • Make sure that the bottle is properly tightened onto the motor/base.
    • Use after fully charged.
  2. Ingredients can't be blended
    Check:
    • Check if your ingredients are too much or too little?
    • If your cut cubes of ingredients are too big?
    • If you've got too little water/milk added?

    Solution:
    • Add enough ingredients.
    • Cut your cubes into smaller cubes.
    • Add water or milk.
  3. Red & green light flickers alternatively, and motor won't start
    Check:
    • If safety mode is activated?
    • If the battery is flat?

    Solution:
    • Retighten the bottle to the motor.
    • Charge the device.
  4. Red light flickers and motor won't start
    Check:
    • If the device is overloaded / blades are blocked?

    Solution:
    • Adjust your ingredients inside your Vitamer.
    • Ensure the blades are free to start spinning.

Charging

For first time use, please fully charge your 380ml Vitamer

LED light is red when charging. LED light is green when it is finished charging.

Easy Assemble

Press the 'on/off' button when the battery is fully charged, the green light will indicate that it is ready to blend.

Easy Wash

When the battery is low, the red and green light will flicker alternately.

VITAMER

400ml

How To Use

Step one
Fully charge your Vitamer

Fully charge until red light changes to green. Please only use your Vitamer charger.

Step two
Add your ingredients

Put your fruit, ice and other ingredients in first, followed by your liquid.

Step three
Connect

Tighten bottle onto motor until green light flashes.

Step four
Blend

Keep your Vitamer upside down, double-click the power button to start and then flip right way up. Tip: if the motor doesn’t switch on, the blades are blocked.

Step five
Auto-clean

Immediately after use, fill the bottle half-full with water, add a drop of soap, blend for 10 seconds, and then rinse the bottle and blades. Do not submerge the motor in water. Ensure your charging port flap is closed.

How to use your Vitamer 400ml

Here is a short video on how to use your Vitamer 400ml Portable Blender.

Fault & Diagnosis

  1. Vitamer won't start
    Check:
    • If used continuously for a long time?
    • If the blade is stuck by ingredients?
    • If the bottle is connected to the motor correctly?
    • If the battery is flat?

    Solution:
    • Wait for the motor to cool down.
    • Remove the ingredients that's stuck - ensure that blades are clear.
    • Make sure that the bottle is properly tightened onto the motor/base.
    • Use after fully charged.
  2. Ingredients can't be blended
    Check:
    • Check if your ingredients are too much or too little?
    • If your cut cubes of ingredients are too big?
    • If you've got too little water/milk added?

    Solution:
    • Add enough ingredients.
    • Cut your cubes into smaller cubes.
    • Add water or milk.
  3. Red & green light flickers alternatively, and motor won't start
    Check:
    • If safety mode is activated?
    • If the battery is flat?

    Solution:
    • Retighten the bottle to the motor.
    • Charge the device.
  4. Red light flickers and motor won't start
    Check:
    • If the device is overloaded / blades are blocked?

    Solution:
    • Adjust your ingredients inside your Vitamer.
    • Ensure the blades are free to start spinning.

Charging

For first time use, please fully charge your 400ml Vitamer

LED light is red when charging. LED light is green when it is finished charging.

Easy Assemble

Press the 'on/off' button when the battery is fully charged, the green light will indicate that it is ready to blend.

Easy Wash

When the battery is low, the red and green light will flicker alternately.

VITAMER

500ml

How To Use

Step one
Fully charge your Vitamer

Fully charge until red light changes to blue. Please only use your Vitamer charger.

Step two
Connect

Tighten bottle onto motor until blue light flashes.

Step three
Add your ingredients

Put your liquid in first, followed by your fruit, ice and other ingredients.

Step four
Blend

Flip your Vitamer upside down, press the power button to start and then flip right way up. Tip: if the motor doesn’t switch on, the blades are blocked.

Step five
Auto-clean

Immediately after use, fill the bottle half-full with water, add a drop of soap, blend for 10 seconds, and then rinse the bottle and blades. Do not submerge the motor in water. Ensure your charging port flap is closed.

How to use your Vitamer 500ml

Here is a short video on how to use your Vitamer 500ml Portable Blender.

Fault & Diagnosis

  1. Vitamer won't start
    Check:
    • If used continuously for a long time?
    • If the blade is stuck by ingredients?
    • If the bottle is connected to the motor correctly?
    • If the battery is flat?

    Solution:
    • Wait for the motor to cool down.
    • Remove the ingredients that's stuck - ensure that blades are clear.
    • Make sure that the bottle is properly tightened onto the motor/base.
    • Use after fully charged.
  2. Ingredients can't be blended
    Check:
    • Check if your ingredients are too much or too little?
    • If your cut cubes of ingredients are too big?
    • If you've got too little water/milk added?

    Solution:
    • Add enough ingredients.
    • Cut your cubes into smaller cubes.
    • Add water or milk.
  3. Red & blue light flickers alternatively, and motor won't start
    Check:
    • If safety mode is activated?
    • If the battery is flat?

    Solution:
    • Retighten the bottle to the motor.
    • Charge the device.
  4. Red light flickers and motor won't start
    Check:
    • If the device is overloaded / blades are blocked?

    Solution:
    • Adjust your ingredients inside your Vitamer.
    • Ensure the blades are free to start spinning.

Charging

For first time use, please fully charge your 500ml Vitamer

LED light is red when charging. LED light is blue when it is finished charging.

Easy Assemble

Press the 'on/off' button when the battery is fully charged, the blue light will indicate that it is ready to blend.

Easy Wash

When the battery is low, the red and blue light will flicker alternately.

VITAMER

500ml Pro

How To Use

Step one
Fully charge your Vitamer

Fully charge until orange light changes to white.

Step two
Connect

Tighten bottle onto blades foundation (do not over-tighten as this may cause the rubber seal below the blades to lift and result in leakage that could damage the motor); then tighten the bottle onto the motor until white light flashes.

Step three
Add your ingredients

Put your liquid in first, followed by your fruit, ice and other ingredients. Note: liquid should not exceed the "max" line indicated on the bottle. If using to crush ice then simply add your ice only.

Step four
Blend

Flip your Vitamer upside down, double-click the power button to start and then flip right way up. Tip: if the motor starts and stops, the blades are blocked. Lightly shaking/twisting your Vitamer at a 45° angle once or twice while the motor is on can help improve your blend.

Step five
Auto-clean

Immediately after use, fill the bottle just below the "max" line with water, add a drop of soap, blend for 10 seconds, and then rinse the bottle and blades. Do not submerge the motor in water. If you would like to remove the grey rubber seal below the blades to thouroughly clean it, please ensure that you refit it correctly (there must be no visible gaps between the white plastic and grey rubber seal) to avoid potential leakage into the motor.

How to use your Vitamer 500ml Pro

Here is a short video on how to use your Vitamer 500ml Pro Portable Blender.

Fault & Diagnosis

  1. Vitamer won't start
    Check:
    • If used continuously for a long time?
    • If the blade is stuck by ingredients?
    • If the bottle is connected to the motor correctly?
    • If the battery is flat?

    Solution:
    • Wait for the motor to cool down.
    • Remove the ingredients that's stuck - ensure that blades are clear.
    • Make sure that the bottle is properly tightened onto the motor/base.
    • Use after fully charged.
  2. Ingredients can't be blended
    Check:
    • Check if your ingredients are too much or too little?
    • If your cut cubes of ingredients are too big?
    • If you've got too little water/milk added?

    Solution:
    • Add enough ingredients.
    • Cut your cubes into smaller cubes.
    • Add water or milk.
  3. Orange & white light flickers alternatively, and motor won't start
    Check:
    •  - If safety mode is activated?
    •  - If the battery is flat?

    Solution:
    •  - Retighten the bottle to the motor.
    •  - Charge the device.
  4. Orange light flickers and motor won't start
    Check:
    •  - If the device is overloaded / blades are blocked?

    Solution:
    •  - Adjust your ingredients inside your Vitamer.
    •  - Ensure the blades are free to start spinning.
  5. There is a smell of burns
    Check:
    •  - If used continuously for a long time?

    Solution:
    •  - High power may cause a burning smell due to friction. Do not worry.

Charging

For first time use, please fully charge your Vitamer 500ml Pro

LED light is orange when charging. LED light is white when it is finished charging.

Easy Assemble

Press the 'on/off' button; the white light will indicate that it is fully charged.

Easy Wash

Press the 'on/off' button; the flickering white/orange light will indicate that the battery is low.

Easy Wash

Press the 'on/off' button; the light remains off indicating that the battery is flat.

Easy Wash

Sleep mode: after 15sec of not using your Vitamer, it will enter sleep mode barely consuming power.

Easy Wash

Please fully charge your Vitamer before using. Be sure to user your 5V1-2A adapter. If you user an adapter over 5V, it may cause damage.